...the relation of betweenness on the torus is undetermined for curves that cannot be contracted to a point [e.g., circles around a doughnut hole], i.e., for three of such curves it is not uniquely determined which of them lies between the other two. ..This indeterminateness... has the consequence that such a curve [alone] does not divide the surface of the torus into two separate domains; between points to the "right" and to the "left" of the line.
German–American philosopher
Hans Reichenbach (26 September 1891 – 9 April 1953) was a leading philosopher of science, educator and proponent of logical positivism.
From: Wikiquote (CC BY-SA 4.0)
...the stereographic projection of the spherical surface. From the north pole P we draw radial lines to project every point of the surface of the sphere upon the horizontal plane [below, perpendicular to a line joining it to P and the sphere's center]. In general this transformation is unique and continuous , although the metrical relations are distorted; for the point P, however, it shows a singularity. Point P is mapped upon the infinite; i.e., no finitely located point of the plane corresponds to it. It can be shown that every transformation possesses a singularity in at least one point. The surface of the sphere is therefore called topologically different from the plane. Only a "sphere without a north pole" [point] would be topologically equivalent to a plane. ...such a sphere has a point-shaped hole without a boundary and is no longer a closed surface.
The surfaces of three-dimensional space are distinguished from each other not only by their curvature but also by certain more general properties. A spherical surface, for instance, differs from a plane not only by its roundness but also by its finiteness. Finiteness is a holistic property. The sphere as a whole has a character different from that of a plane. A spherical surface made from rubber, such as a balloon, can be twisted so that its geometry changes. ...but it cannot be distorted in such a way as that it will cover a plane. All surfaces obtained by distortion of the rubber sphere possess the same holistic properties; they are closed and finite. The plane as a whole has the property of being open; its straight lines are not closed. This feature is mathematically expressed as follows. Every surface can be mapped upon another one by the coordination of each point of one surface to a point of the other surface, as illustrated by the projection of a shadow picture by light rays. For surfaces with the same holistic properties it is possible to carry through this transformation uniquely and continuously in all points. Uniquely means: one and only one point of one surface corresponds to a given point of the other surface, and vice versa. Continuously means: neighborhood relations in infinitesimal domains are preserved; no tearing of the surface or shifting of relative positions of points occur at any place. For surfaces with different holistic properties, such a transformation can be carried through locally, but there is no single transformation for the whole surface.
If heat were the affecting force, direct indications of its presence could be found which would not make use of geometry as an indirect method. ...direct evidence for the presence of heat is based on the fact that it affects different materials in different ways. ...The forces... which we have introduced... have two properties: (a) They affect all materials in the same way. (b) There are no insulating [or isolating] walls. ...the definition of the insulating wall may be added here: it is a covering made of any kind of material which does not act upon the enclosed object with forces having property a. Let us call the forces which have the properties a and b universal forces; all other forces are called differential forces. Then it can be said that differential forces, but not universal forces, are directly demonstrable.
Try QuoteGPT
Chat naturally about what you need. Each answer links back to real quotes with citations.
It is remarkable that this generalization of plane geometry to surface geometry is identical with that generalization of geometry which originated from the analysis of the axiom of parallels. ...the construction of non-Euclidean geometries could have been equally well based upon the elimination of other axioms. It was perhaps due to an intuitive feeling for theoretical fruitfulness that the criticism always centered around the axiom of parallels. For in this way the axiomatic basis was created for that extension of geometry in which the metric appears as an independent variable. Once the significance of the metric as the characteristic feature of the plane has been recognized from the viewpoint of Gauss' plane theory, it is easy to point out, conversely, its connection with the axiom of parallels. The property of the straight line as being the shortest connection between two points can be transferred to curved surfaces, and leads to the concept of straightest line; on the surface of the sphere the great circles play the role of the shortest line of connection... analogous to that of the straight line on the plane. Yet while the great circles as "straight lines" share the most important property with those of the plane, they are distinct from the latter with respect to the axiom of the parallels: all great circles of the sphere intersect and therefore there are no parallels among these "straight lines". ...If this idea is carried through, and all axioms are formulated on the understanding that by "straight lines" are meant the great circles of the sphere and by "plane" is meant the surface of the sphere, it turns out that this system of elements satisfies the system of axioms within two dimensions which is nearly identical in all of it statements with the axiomatic system of Euclidean geometry; the only exception is the formulation of the axiom of the parallels. The geometry of the spherical surface can be viewed as the realization of a two-dimensional non-Euclidean geometry: the denial of the axiom of the parallels singles out that generalization of geometry which occurs in the transition from the plane to the curve surface.